Replace Lock on Your UPVC Door Yourself
You can replace your lock on a upvc door by yourself as long as both sides of the handle plate are accessible. You'll need a screwdriver, a long bolt and a key.
Sometimes a uPVC door mechanism may become stuck because it's not properly lubricated or because something inside has broken. If you know what to do, it's simple to repair.
Preparing for Repairs
uPVC doors can be subject to a myriad of issues and some are more severe than others. If your uPVC door lock is stuck or misaligned, it's possible that you may be in a position to fix the problem yourself. However, it is important to ensure that you do not to do any damage to the mechanism of the lock since this can make the situation much worse. It is also recommended to avoid using lubricants like grease or oil, which could cause the locking mechanism to become sticky. Instead, you should choose a light machine oil or graphite powder as these are safer and won't harm your uPVC door.
A uPVC barrel for a door lock can be quite difficult to take off once it's been installed, so take a careful look at what you're doing prior to starting. If you are not experienced with this kind of repair, you should seek the assistance of a locksmith to ensure that the job is done correctly. This will also help you save time as they can complete the task quickly and effectively.
Repair My Windows And Doors is removing the screw which holds the barrel in place. This screw should be a different colour to the other screws on the door. It is located close to the faceplate of the lock, in the inner edge. After removing the screw, you can slide the barrel out. Once the lock has been removed, you can remove the handle.
It is crucial to understand that a locked uPVC can be opened and shut without the handle. The uPVC door comes with an integrated security system, referred to as multi-point locking. This system consists of two hooks on the sides and top of the door, as well as dead bolt or latch in the middle. This makes a very sturdy and secure door.
If you're unable to open your uPVC doors, it is most likely the locking cylinder. A uPVC door lock is designed to be fitted with a key, and it isn't as simple to break or move as other types of locks. If you're not familiar with this kind of repair, it's advisable to get an expert locksmith.
Removal of the Cylinder
The cylinder is a small part of the handle on a uPVC uPVC that lets you lock or unlock the door. It is commonly made from pin-based technology and although it has been effective for a long time but it is now being targeted by criminals seeking to increase their chances of gaining entry into your home. By replacing the cylinder with a higher-grade lock, you will be able to significantly increase the security of your home without the need to purchase an entire new locking mechanism.
The first step is to remove the handle from the door by loosening the screws that secure it with a Phillips-head screwdriver. Save these screws to reuse them to attach the handle once the job is completed. Find the pinhole that binds the handle to the trim. Find a paper clip or other pin that can be straightened and then placed into the hole. Apply pressure to the pin while rotating the handle until it releases. When it is released, pull the handle towards you to pull back the latch within the cylinder.
Once you have loosened the old cylinder, it is possible to remove it manually. Be careful not damage the threads on either side of cylinder, or the cam in the middle. If the cylinder isn't sliding out easily, it may be being held by the handle furniture or the locking mechanism and must be released to allow it to be able to slide out.
If you're ready to replace the cylinder, search for one that has been rated by an independent testing agency to meet the minimum standards for anti-snap as well as anti-bump security. There are a variety of grades of locks available on the market, so it is important to know the requirements prior to deciding to select the replacement.
If you are able, bring the old cylinder with you to the store to make sure that you are purchasing a matching replacement. There are about 25 different sizes of lock cylinders to choose from, so it is essential to accurately measure yours.
Reinstalling Cylinder
If your locks aren't working correctly, you may need to replace them. This can be done for a variety of reasons, including increasing security or ensuring that you meet insurance requirements. It is possible to replace the lock if you have lost keys, or you recently relocated. Whatever the reason, replacing your uPVC door lock isn't an overwhelming task and can be done by anyone with a bit of guidance.
First, ensure that the door is propped or secured so that it does not close during the procedure. The next step is to take off the screws that keep the handle in place with a screwdriver. Remove the screws gradually, or small pieces may fall off. Slide out the interior and exterior handles simultaneously after taking out the screws. It's a bit tricky however, you should not push anything. Doing so can break the handles, and could cause damage to the handle mechanism.
Locate the cylinder screw on the edge of the door after removing the handles. It's usually a large screw that's line with the lower part of the cylinder. It should have a different colour from the other screws and easy to identify. Twist the screw to loosen it and then remove it.
After removing the screw you should be able to observe the cylinder inside its socket. Insert your key and turn it to both left and right positions. This will help unlock the cylinder. When the cylinder is unlocked, you'll have to gently tug it out of the socket.
Once you've removed the old cylinder, put the new one into its socket. If you are having trouble, try wiggling or tugging again. If you're not able to get the cylinder in, consider replacing the lock entirely.
If you are replacing a euro cylinder, be sure to purchase one with anti-snap and/or anti-bump security. These features will increase the security of your home and make it more difficult for burglars to get around the lock.
Reinstalling the Handle
There are a few reasons your uPVC handle may not be working properly. Most of the time, it's a result of general wear and tear, but at other times the problem is more serious. It could be that the cylinder for the lock is damaged and cannot be repaired and it's time to replace it with a brand new one.
First, you will need to remove the old handle. This isn't difficult to do and you can usually accomplish this by removing the two screws that hold the handle in place using the help of a screwdriver. Once the screws are removed there should be nothing holding the handle to the door. it should be able to pull away with very little effort.
Once you have removed the handle, it's an ideal idea to clean down the back plate and spindle hole to ensure there is no dirt or grime the area that could cause problems when you replace the handle. It's also an excellent idea to give the handle a clean with a cloth to ensure that it's free of dirt and dust because this could affect the performance of the handle.
Before you reinstall the new handle, take the time to look at how it fits on the door. In most cases, the hook plate and roller face plate are able to fit into a recess in the centre lock case, so that there is no gap between them. If the handles don't fit correctly, they could cause pressure on the central lock case and cause it to break.
Begin by slipping the spindle through the hole on the exterior handle, and then into hole of the interior handle. It is possible to tap the spindle lightly with a hammer or mallet to get it to slide into place. Once you've secured it, there is probably a small retaining screw on the end of the spindle. you must tighten to align the holes, and then replace this screw.